Chevrolet Sonic manuals

Chevrolet Sonic Repair Manual: 3-5-Reverse and 4-5-6 Clutch Fluid Seal Ring Replacement (Gen 2)

Chevrolet Sonic Repair Manual / Powertrain / Transmission/Transaxle / Automatic / General / 3-5-Reverse and 4-5-6 Clutch Fluid Seal Ring Replacement (Gen 2)



3-5-Reverse and 4-5-6 Clutch Fluid Seal Ring Replacement

Callout

Component Name

Special Tools

DT-46620 Seal Installer

For equivalent regional tools, refer to Special Tools.

1

3? Reverse and 4?? Clutch Fluid Seals (Qty: 3)

Procedure

  1. Place DT-46620-3 which is part of DT-46620 seal installer over the case hub and adjust it so that only the bottom seal ring is exposed.
  2. Place a NEW fluid seal ring onto DT-46620-3 which is part of DT-46620 seal installer .
  3. Use DT-46620-2 which is part of DT-46620 seal installer to push the fluid seal ring down over DT-46620-3 which is part of DT-46620 seal installer into the hub ring groove.
  4. Repeat the above steps to install all 3 seal rings, adjusting DT-46620-3 which is part of DT-46620 seal installer to the appropriate ring groove.

2

Small Chamfer Up

Caution:

Do not force the seal installer down over the seals as this will roll and damage the seals. The large chamfer is designed to fit over the over stretched seal. Use a hand to help shrink the seal if the seal installer is difficult to install over the seal rings.

Procedure

Install DT-46620-1 which is part of DT-46620 seal installer with the large chamfer end down over the fluid seal rings and leave DT-46620-1 which is part of DT-46620 seal installer on the seals for at least 60 seconds.

3

Large Chamfer Up

Procedure

  1. Install DT-46620-1 which is part of DT-46620 seal installer with the small chamfer end facing down for at least 60 seconds. This will properly size the bottom seal ring.
  2. Leaving DT-46620-1 which is part of DT-46620 seal installer on the fluid seal rings for an extended period of time could cause a fluid leak on the initial clutch piston circuit until the seal rings warm up and expand to the proper dimension.
3-5-Reverse and 4-5-6 Clutch Fluid Seal Ring Replacement (Gen 1)
3-5-Reverse and 4-5-6 Clutch Fluid Seal Ring Replacement Callout Component Name Special Tools DT-46620 Seal Installer For e ...

3-5-Reverse and 4-5-6 Clutch Housing Assemble (6T30/40/45/50 - Gen 2)
Table 1: 4?? Clutch Piston Installation Table 2: 4?? Clutch Fluid Dam Installation Table 3: 3? Reverse Clutch Plates Installation Table 4: Reluctor Wh ...

Other materials:

Tire Rotation
Tires should be rotated every 12 000 km (7,500 mi). See Maintenance Schedule. Tires are rotated to achieve a uniform wear for all tires. The first rotation is the most important. Anytime unusual wear is noticed, rotate the tires as soon as possible, check for proper tire inflation pressure, an ...

Rear Side Door Trim Replacement (Sedan)
Rear Side Door Trim Replacement Callout Component Name 1 Rear Side Door Inside Handle Bolt Cap 2 Rear Side Door Inside Handle Fastener Caution: Refer to Fastener Caution. Proce ...

Fuel Tank Filler Pipe Replacement
Removal Procedure Remove the bracket fastener (1). Lift and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the fuel tank filler pipe bracket fastener (1). Disconnect the vent hose (2). Refer to Plastic Collar ...

В© 2014-2024 Copyright www.csmans.com
 
0.0075