Table 1: | Turbine Shaft, Reluctor Wheel and Piston Removal |
Table 2: | 4?? Clutch Plate Removal |
Table 3: | 4?? Clutch Piston Removal |
Table 4: | Reluctor Wheel and Piston Removal |
Table 5: | 3? Reverse Clutch Plate Removal |
Callout |
Component Name |
---|---|
1 |
Turbine Shaft Retainer Ring Note: Discard the retainer ring. It is not re-usable. Special Tools
GE 5586-A Snap Ring Pliers or equivalent For equivalent regional tools, refer to Special Tools. |
2 |
Turbine Shaft |
3 |
Reaction Carrier Hub Assembly |
4 |
Reaction Carrier Hub Thrust Bearing Assembly |
Callout |
Component Name |
---|---|
1 |
4?? Clutch Backing Plate Retaining Ring |
2 |
4?? Clutch Backing Plate |
3 |
4?? Clutch Plate Assembly (Qty: 5) |
4 |
4?? Clutch Plate (Gen 2 ?#8201;Qty: 5) |
Callout |
Component Name |
---|---|
1 |
4?? Clutch Dam Retaining Ring Note: The 4-5-6 clutch dam retaining ring is not reusable.
For equivalent regional tools, refer to Special Tools. |
2 |
4?? Clutch Piston Fluid Dam Assembly Procedure
|
3 |
4?? Clutch Piston Return Spring Assembly |
4 |
4?? Clutch Piston Note: Apply shop air to the 4?? clutch feed hole using a rubber tipped air gun to dislodge the clutch piston. |
5 |
4?? Clutch Piston Inner Seal |
6 |
4?? Clutch Piston Outer Seal (Dark Blue) (Stepped) |
7 |
4?? Clutch Piston Outer Seal (Large) (Rounded) |
Callout |
Component Name |
---|---|
1 |
Input Shaft Speed Sensor Reluctor Ring Retainer Ring Caution: Compress the reluctor wheel just enough to clear the retainer. Over compressing the reluctor wheel will break the alignment tab and the clutch housing. Special Tool
DT-47694 Piston Spring Compressor For equivalent regional tools, refer to Special Tools. |
2 |
Input Shaft Speed Sensor Reluctor Wheel |
3 |
3? Reverse Clutch Piston |
4 |
3? Reverse Clutch Piston Return Spring Assembly |
5 |
3? Reverse Clutch Piston Inner (Reluctor) Seal (Orange) |
6 |
3? Reverse Clutch Piston Inner Seal |
7 |
3? Reverse Clutch Piston Dam Seal (Black) |
Callout |
Component Name |
---|---|
1 |
3? Reverse Clutch Backing Plate Ring Retainer Ring Note: Gently push down on the backing plate to get enough clearance between the backing plate and retainer. |
2 |
3? Reverse Clutch Backing Plate |
3 |
3? Reverse Clutch Plate Assembly (Qty: 3) |
4 |
3? Reverse Clutch Plate (Qty: 3) |
5 |
3? Reverse Clutch Apply Plate (Waved) |
Sunroof Housing Front Drain Hose Replacement
Sunroof Housing Front Drain Hose Replacement
Callout
Component Name
Preliminary Procedure
It is only necessary to lower the headliner. Only do those steps in the
headliner replacement procedure that will lower the headliner ...
Driver or Passenger Seat Back Cushion Heater Replacement
Driver or Passenger Seat Back Cushion Heater Replacement
Callout
Component Name
Warning: Refer to SIR Warning.
Preliminary Procedure
Remove the driver or passenger seat. Refer to Driver or Passenger
Seat Remov ...
Wheel Drive Shafts Description and Operation
Front wheel drive axles are flexible assemblies.
Front wheel drive axles consist of the following components:
A front wheel drive shaft tripot joint (inner joint)
A front wheel drive shaft constant velocity joint (outer joint)
A front wheel drive shaft
The front wheel drive shaft connec ...