Chevrolet Sonic Repair Manual: Body
- General
- Body Hinge Pillar Lower Reinforcement Replacement
- Body Waterleak Repair
- Dimensions - Body (4NB)
- Dimensions - Body (5HB)
- Eliminating Unwanted Odors in Vehicles
- Front Hinge Pillar Body Sectioning
- General Plastic Repair
- How to Identify Plastic Parts
- Plastic Collar Quick Connect Fitting Service
- Plastic Collar Quick Connect Fitting Service
- Plastic Collar Quick Connect Fitting Service
- Plastic Identification and Refinishing Systems
- Rear Brake Hose Replacement (Body to Axle - Disc Brake)
- Rear Brake Hose Replacement (Body to Axle - Drum Brake)
- Body Electrical
- Doors and Enclosures
- Body Exterior
- Information
- Spoilers/Aero
- Bumpers
- Emblems/Decals/Paint
- Front Grille
- Garnish/Finishers/License
- Identification Plates
- Moldings
- Panels
- Trunk Bed
- Weatherstripping
- Frame and Structure
- Body Side Frame Rocker Reinforcement Replacement
- Driver or Passenger Seat Back Cushion Frame Replacement
- Driver or Passenger Seat Cushion Frame Replacement
- Drivetrain and Front Suspension Frame Replacement
- Front Compartment Front Insulator Cover Replacement
- Front Wheelhouse Liner Inner Front Extension Replacement (Left SIde)
- Front Wheelhouse Liner Inner Front Extension Replacement (Right SIde, LWE, LUW)
- Front Wheelhouse Liner Inner Front Extension Replacement (Right Side, LUV)
- Front Wheelhouse Liner Replacement (Front)
- Front Wheelhouse Liner Replacement (Rear)
- Rear Wheelhouse Liner Replacement (Hatchback - Left)
- Rear Wheelhouse Liner Replacement (Hatchback - Right)
- Rear Wheelhouse Liner Replacement (Sedan - Left)
- Rear Wheelhouse Liner Replacement (Sedan - Right)
- Rear Wheelhouse Panel Liner Extension Replacement
- Special Tools
- Center Pillar Reinforcement Replacement
- Drivetrain and Front Suspension Frame Skid Plate Replacement
- Glass & Windows
- Driver Info & Control
- Body Interior
- Arm Rests
- Center Console
- Cup Holders
- Dashboard Assembly
- Floorlining and Carpets
- Grab Handles
- Headlining
- Storage and Pockets
- Trim Panels/Welts
- Mirrors
- Mirror Adjustment
- Outside Mirror Description and Operation
- Inside Rearview Mirror Replacement
- Outside Rearview Mirror Glass Replacement
- Outside Rearview Mirror Housing Rear Cover Replacement
- Outside Rearview Mirror Housing Replacement
- Outside Rearview Mirror Motor Replacement
- Outside Rearview Mirror Remote Control Switch Replacement
- Outside Rearview Mirror Replacement (Manual)
- Outside Rearview Mirror Replacement (Power)
- Restraints
- Inflatable Restraint Sensing and Diagnostic Module Programming and Setup
- Primary
- Restraints Control
- Secondary
- Air Bag Modules
- Roof - Fixed, Leisure
- Airbag Roof Side Rail Module Replacement - Rear
- Roof Front Header Panel Replacement
- Roof Outer Panel Replacement (4NB)
- Roof Outer Panel Replacement (5HB)
- Roof Rail Front Assist Handle Replacement
- Roof Rail Rear Assist Handle Replacement
- Roof Rear Header Panel Replacement (5HB)
- Moonroof/Sunroof
- Roof Drainage
- Seating
- Wipers, Washers
Towing the Vehicle
Notice: Incorrectly towing a disabled vehicle may cause damage. The
damage would not be covered by the vehicle warranty. Do not lash or hook to
the chassis components including the front and ...
General
...
Other materials:
Brake Fluid
The brake/clutch master cylinder reservoir is filled with DOT 3 brake fluid as
indicated on the reservoir cap. See Engine Compartment Overview for
the location of the reservoir.
There are only two reasons why the fluid level in the reservoir might go down:
The fluid level goes down ...
Tire Terminology and Definitions
Air Pressure
The amount of air inside the tire pressing outward on each square inch
of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per
square inch).
Accessory Weight
The combined weight of optional accessories. Some examples of optional
access ...
Tire and Wheel Assembly-to-Hub/Axle Flange Match-Mounting
Note: After remounting a tire and wheel assembly to a hub/axle flange,
remeasure the tire and wheel assembly on-vehicle runout in order to verify that
the amount of runout has been reduced and brought to within tolerances.
Mark the location of the high spot on the tire and wheel asse ...
0.0145