Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Brake Pressure Modulator Valve Pipe Replacement

Chevrolet Sonic Repair Manual / Chassis / Brakes / General / Brake Pressure Modulator Valve Pipe Replacement

Removal Procedure

Warning:

Refer to Brake Fluid Irritant Warning.

Caution:

Refer to Brake Fluid Effects on Paint and Electrical Components Caution.

Caution:

Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.

  1. Remove the battery. Refer to Battery Replacement.
  2. Clean the area surrounding the brake pressure modulator valve (BPMV) of any accumulated dirt and debris.

  3. Disconnect the master cylinder secondary brake pipe fitting (1) from the master cylinder.
  4. Plug the master cylinder outlet port to prevent brake fluid loss and contamination.

  5. Disconnect the master cylinder secondary brake pipe fitting (1) from the BPMV.
  6. Plug the BPMV inlet port to prevent brake fluid loss and contamination.
  7. Remove the master cylinder secondary brake pipe assembly.

  8. Disconnect the master cylinder primary brake pipe fitting (1) from the master cylinder.
  9. Plug the master cylinder outlet port to prevent brake fluid loss and contamination.

  10. Disconnect the master cylinder primary brake pipe fitting (1) from the BPMV.
  11. Plug the BPMV inlet port to prevent brake fluid loss and contamination.
  12. Remove the master cylinder primary brake pipe assembly.
Installation Procedure
  1. Install the master cylinder primary brake pipe assembly.

    2. Caution:

    Refer to Fastener Caution.

  2. Connect the master cylinder primary brake pipe fitting (1) to the BPMV and tighten to  18 Y (13 lb ft)

    .



  3. Connect the master cylinder primary brake pipe fitting (1) to the master cylinder and tighten to  18 Y (13 lb ft)

    .

  4. Install the master cylinder secondary brake pipe assembly.

  5. Connect the master cylinder secondary brake pipe fitting (1) to the BPMV and tighten to  18 Y (13 lb ft)

    .



  6. Connect the master cylinder secondary brake pipe fitting (1) to the master cylinder and tighten to  18 Y (13 lb ft)

    .

  7. Install the battery. Refer to Battery Replacement.
  8. Bleed the hydraulic brake system. Refer to Hydraulic Brake System Bleeding.
Brake Pressure Modulator Valve Bracket Replacement
Removal Procedure Remove the brake pressure modulator valve (BPMV) and bracket assembly. Refer to Brake Pressure Modulator Valve Replacement. Remove the BPMV boltsR ...

Brake Pressure Modulator Valve Replacement
Removal Procedure Warning: Refer to Brake Fluid Irritant Warning. Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution. Caution: Always ...

Other materials:

Power Door Locks
Select Power Door Locks and the following may display: Auto Door Unlock Unlock Door Anti Lock Out Delayed Door Lock Auto Door Unlock This allows selection of which of the doors will automatically unlock when the vehicle is shifted into P (Park) or the key is removed. Select All Doors, ...

Front Compartment Front Insulator Cover Replacement
Front Compartment Front Insulator Cover Replacement Callout Component Name 1 Front Compartment Front Insulator Cover Screw (Qty:?€‰2) Caution: Refer to Fastener Caution. Tighten 2.5?€‰Y (22?₠...

Clutch Pedal Position Sensor Replacement
Removal Procedure Remove the instrument panel lower trim pad cover. Refer to Instrument Panel Lower Trim Pad Cover Replacement. Remove the clutch pedal position sensor bolt (2). Remove the clutch pedal position sensor (1). Disconnect the clu ...

© 2014-2024 Copyright www.csmans.com
 
0.0101