Chevrolet Sonic manuals

Chevrolet Sonic Repair Manual: Engine Front Cover and Oil Pump Assemble

Chevrolet Sonic Repair Manual / Powertrain / Engine / Engine Block / Cylinder Block / Engine Front Cover and Oil Pump Assemble

Oil Pump Installation


    Note:

    The oil pump slide spring and pin, as well as the slide seal and slide seal spring can be ordered as single parts. All other oil pump components can only be ordered as a replacement kit.

  1. Install the oil pump components in the following order:
    1. Note:

      The bore (8) in the oil pump slide must fit smooth-running and without clearance to the oil pump slide pivot pin (7).

    2. Install the oil pump slide (6).
    3. Install the inner oil pump vane ring (5).
    4. Note:

      Mind the installation position of the oil pump vane rotor (4). The mark (9) must point to direction of the oil pump cover.

    5. Install the oil pump vane rotor (4).
    6. Note:

      Mind the localized flats (3) on the oil pump vanes (2) caused by the oil pump vane rings. The localized flats must point to the oil pump vane rotor.

    7. Install the 6 oil pump vanes (2).
    8. Install the outer oil pump vane ring (1).

  2. Install the 2 oil pump slide seals and the 2 oil pump slide seal springs (2) in the position as shown to the 2 grooves (1) of the oil pump slide.

  3. Protect the engine front cover edge (5) with a suitable piece of plastic.
  4. Note:

    The length of the removed oil pump slide spring (2) should be 76.5 mm (3.0118 in) for suction engines and 61 mm (2.4016 in) for turbo engines.

  5. Install the oil pump slide spring pin along with the oil pump slide spring (4). Use a screwdriver to compress the oil pump slide spring. The flat side of oil pump slide spring pin must face upwards.
  6. Measure the oil pump clearances to ensure a correct installation of the oil pump components. Refer to Engine Front Cover and Oil Pump Cleaning and Inspection.
  7. Lubricate the oil pump vanes, the oil pump vane rotor, the oil pump slide spring and the area (3) with engine oil.
  8. Inspect the oil pump slide spring mechanism for functionality.

  9. Install the oil pump cover (2) and the 8 oil pump cover bolts (1).

  10. Caution:

    Refer to Fastener Caution.

  11. Tighten the oil pump cover bolts in a sequence as shown to 8 Y (71 lb in)

    .



  12. Install the crankshaft balancer (1) and rotate in the direction shown (2) in order to inspect the function of the oil pump mechanism. The crankshaft balancer should rotate easily.
Engine Front Cover Assemble

    Install the crankshaft front oil seal (10).
  1. Install the crankshaft front oil seal (10).
  2. Install the oil pressure relief valve (7), (8) and (9) and tighten to 50 Y (37 lb ft)

    .

  3. Install the exhaust camshaft position sensor (5) and the seal ring (4).
  4. Install the exhaust camshaft sensor bolt (6) and tighten to 6 Y (53 lb in)

    .

  5. Install the intake camshaft position sensor (2) and the seal ring (3).
  6. Install the intake camshaft sensor bolt (1) and tighten to 6 Y (53 lb in)

    .

Engine Front Cover Gasket Removal
Remove and DISCARD the engine front cover gasket (1). ...

Engine Front Cover and Oil Pump Cleaning and Inspection
Engine Front Cover Cleaning Procedure Clean the engine front cover sealing surface. Warning: Wear safety glasses when using compressed air in order to prevent eye injury. ...

Other materials:

Automatic Transmission Shift Lock Control Function Check
Warning When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface. 2. Apply the parking brake. Be ready to ap ...

OnStar Overview
If equipped, this vehicle has a comprehensive, in-vehicle system that can connect to a live Advisor for Emergency, Security, Navigation, Connection, and Diagnostic Services. The OnStar system status light is next to the OnStar buttons. If the status light is: Solid Green: System is ...

Rear Wheel Bearing and Hub Replacement (Disc Brake)
Special Tools EN–45059 Angle Meter For equivalent regional tools, refer to Special Tools. Removal Procedure Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Insta ...

© 2014-2022 Copyright www.csmans.com
 
0.0078