Chevrolet Sonic manuals

Chevrolet Sonic Repair Manual: Front End Upper Tie Bar Replacement

Chevrolet Sonic Repair Manual / Chassis / Steering / Tie Rods and Linkage / Front End Upper Tie Bar Replacement

Removal Procedure

    Warning:

    Refer to Approved Equipment for Collision Repair Warning.

    Warning:

    Refer to Glass and Sheet Metal Handling Warning.

  1. Disable the SIR System. Refer to SIR Disabling and Enabling.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  3. Remove all related panels and components.
  4. Visually inspect the damage. Repair as much of the damage as possible.
  5. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.


  6. Locate and mark all the necessary factory welds of the front upper tie bar assembly.
  7. Drill all factory welds. Note the number and location of welds for installation of the service assembly.
  8. Remove the front end upper tie bar support bolts (1) and front end upper tie bar bolts (2).
  9. Remove the front end upper tie bar assembly (3).
Installation Procedure

    Drill 8 mm (5/16 in) plug weld holes as necessary on service parts,
  1. Drill 8 mm (5/16 in) plug weld holes as necessary on service parts, in the locations noted from the original assembly (1).
  2. Clean and prepare the mating surface for welding, as necessary.

  3. Position the front upper tie bar support (1) and front upper tie bar (2) on the vehicle
  4. Verify the fit of the front end upper tie bar.
  5. Caution:

    Refer to Fastener Caution.

  6. Install the front upper tie bar support bolts (3) and tighten to 22 Y (16 lb ft)

    .

  7. Install the front upper tie bar bolts (4) and tighten to 9 Y (80 lb in)

    .



  8. When the service assembly is correctly positioned, plug weld accordingly (1).
  9. Measure frequently to ensure proper fit and alignment.
  10. Clean and prepare all welded surfaces.
  11. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
  12. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems.
  13. Install all related panels and components.
  14. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  15. Enable the SIR system. Refer to SIR Disabling and Enabling.
Tie Rods and Linkage
...

Front End Upper Tie Bar Replacement
Front End Upper Tie Bar Replacement Callout Component Name Preliminary Procedures Disable the SIR system. Refer to SIR Disabling an ...

Other materials:

Door Lock and Ignition Lock Folding and Non-Folding Key Cutting
High Security keys are available from the service parts system. Obtain the key code from the security card or from the GM Dealer World, Parts, Key Code Look Up system. If you have the key code and access to a Triax-E., BD Laser or other code key cutting machine from the GM Dealer Equipment C ...

Headlining Trim Panel Replacement (Hatchback without Sunroof)
Headlining Trim Panel Replacement Callout Component Name Warning: Do not attempt to repair or alter the head impact energy-absorbing material glued to the headliner or to the garnish trims. If the material is damaged ...

Turbocharger Oil Feed Pipe Replacement
Removal Procedure Open the hood. Disconnect battery negative cable. Refer to Battery Negative Cable Disconnection and Connection. Remove the exhaust manifold heat shield. Refer to Exhaust Manifold Heat Shield Replacement. Remove the turbocharger oil feed p ...

В© 2014-2026 Copyright www.csmans.com
 
0.0064