Chevrolet Sonic manuals

Chevrolet Sonic Repair Manual: HVAC System Control Module Programming and Setup

Chevrolet Sonic Repair Manual / HVAC / General / HVAC System Control Module Programming and Setup

Note:

  • DO NOT program a control module unless directed to by a service procedure or a service bulletin. If the control module is not properly configured with the correct calibration software, the control module will not control all of the vehicle features properly.
  • Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector. If there is an interruption during programming, programming failure or control module damage may occur.
  • Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will interrupt programming. When required install the EL-49642 SPS Programming Support Tool to maintain system voltage. If not available, connect a fully charged 12 V jumper or booster pack disconnected from the AC voltage supply. DO NOT connect a battery charger.
  • Turn OFF or disable systems that may put a load on the vehicles battery such as; interior lights, exterior lights (including daytime running lights), HVAC, radio, etc.
  • During the programming procedure, follow the SPS prompts for the correct ignition switch position.
  • Clear DTCs after programming is complete. Clearing powertrain DTCs will set the Inspection/Maintenance (I/M) system status indicators to NO.
Reference Information
Special Tools

EL-49642 SPS Programming Support Tool

For equivalent regional tools, refer to Special Tools.

Replace and Program Control Module or Reprogram Control Module

To program a replacement or an existing control module, perform the following procedure:

  1. Install EL-49642 SPS Programming Support Tool.
  2. Access the Service Programming System (SPS) and follow the on-screen instructions.
  3. On the SPS Supported Controllers screen, select HVAC Control Module - Programming and follow the on-screen instructions.
  4. On the SPS Supported Controllers screen, select HVAC Control Module - Setup and follow the on-screen instructions.
  5. On the SPS Supported Controllers screen, select HVAC Control Module - Configuration and follow the on-screen instructions.
  6. At the end of programming, choose the “Clear All DTCs” function on the SPS screen.
  7. With a scan tool, perform the Actuator Recalibration Function. Refer to Actuator Recalibration.
Unsuccessful Programming Recovery

In the event of an interrupted or unsuccessful programming event, perform the following steps:

  1. Ignition ON. Ensure the control module, DLC and programming tool connections are secure and the SPS software is up to date.
  2. Verify the control module can be reprogrammed.
  • If the control module cannot be reprogrammed
  1. Ignition OFF for one minute, ignition ON.
  2. Verify the control module can be reprogrammed.
  • If the control module cannot be reprogrammed, replace the control module.
  • If the control module can be reprogrammed.
  • All OK.
    • If the control module can be reprogrammed
  • All OK.
  • Repair Instructions

    Perform the Diagnostic Repair Verification after completing the repair.

    Control Module References for Control Module replacement, programming and setup

    HVAC Component Replacement Reference
    HVAC Component Replacement Reference Scan Tool Name Component Code / Schematic Name Service Name Repair Instruction Name ...

    Manual HVAC Description and Operation
    The air temperature and the air delivery description and operation are divided into five areas: HVAC Control Components Air Speed Air Delivery Heating and A/C Operation Recirculation Op ...

    Other materials:

    Wheel Drive Shafts Description and Operation
    Front wheel drive axles are flexible assemblies. Front wheel drive axles consist of the following components: A front wheel drive shaft tripot joint (inner joint) A front wheel drive shaft constant velocity joint (outer joint) A front wheel drive shaft The front wheel drive shaft connec ...

    Oil Level Indicator and Tube Installation
    Install a NEW oil level indicator tube gasket. Install the oil level indicator tube (2). Caution: Refer to Fastener Caution. Install the oil level indicator tube bolt (1) and tighten to 15 Y (11 lb ft). Install the oil dipstick. ...

    Fuel System Description
    Fuel System Overview The fuel system is an electronic returnless on-demand design. A returnless fuel system reduces the internal temperature of the fuel tank by not returning hot fuel from the engine to the fuel tank. Reducing the internal temperature of the fuel tank results in lo ...

    © 2014-2024 Copyright www.csmans.com
     
    0.0094