Chevrolet Sonic Repair Manual: Immobilizer System Component Programming

Chevrolet Sonic Repair Manual / Accessories / Security & Keyless Entry / Immobilizer / Immobilizer System Component Programming

This procedure will learn the immobilizer function. If the battery voltage is low, charge the battery before proceeding with the learn. If the body control module (BCM) or engine control module (ECM) have been replaced, they must be programmed before performing this learn procedure.

Depending on the immobilizer function being learned or the component replaced, different learn functions are required to be performed. These learn functions are as follows:

Immobilizer System Component Programming
Function name on SPS tool:	Function description:	When the function should be used:	Notes:
Body Control Module IMMO Function with Existing Transponder or Remote Key	The BCM will relearn the immobilizer passwords and data while reusing the existing vehicle keys	The BCM has been replaced and the existing vehicle keys are being reused or a diagnostic has instructed to perform the learn	—
Body Control Module IMMO Function with New Transponder or Remote Key	The BCM will relearn the immobilizer passwords and data while using new vehicle keys	The BCM has been replaced and new vehicle keys are being reused	—
Engine Control Module IMMO Learn	The ECM will relearn the immobilizer passwords and data	The ECM has been replaced or a diagnostic has instructed to perform the learn	—
Engine Control Module and Body Control Module IMMO Learn	The ECM and BCM will learn new immobilizer passwords and data	Both the ECM and BCM have been replaced (this selection will REQUIRE new vehicle keys be used)	Because both the ECM and BCM have been replaced and are learning new immobilizer passwords and data, all vehicle keys must also be replaced
Program Transponder or Remote Key (Add)	A new vehicle key will learn the immobilizer passwords and data	A new vehicle key is being added (does not affect other vehicle keys)	This function may not be available in all sales regions. Refer to the SPS application to determine if a particular vehicle is able to add keys using this method.
Program Transponder or Remote Key (Delete)	All existing vehicle keys will be invalidated and any desired keys are relearned	All vehicle keys are desired to be invalidated and certain keys relearned or a diagnostic has instructed to perform the learn	This procedure may be used if a customer has had their keys lost or stolen and wishes to invalidate the keys, making them unable to start the vehicle

Connect a scan tool to the vehicle and access SPS.
Turn ON the ignition, with the engine OFF.
Ensure that all power consuming devices are turned OFF on the vehicle.
Select SPS application and follow the on-screen instructions.
Select Reprogram ECU.
Select IMMO Immobilizer Learn – Setup.
Select the appropriate programming function based on the component that was replaced or is being programmed. Refer to the table at the top of this document for assistance in choosing the correct programming function.
Follow the on-screen instructions.
After programming all keys “Programming Complete” is displayed.
Press the lock and unlock button on each transmitter that was programmed. This will awaken each transmitter and allow keyless entry functions to be established.
With a scan tool, clear any DTCs.
Verify each key is operating properly. Operate each of the keyless entry functions using the buttons on the transmitter and then start the vehicle. When verifying operation, make sure that no other keys are near the vehicle.

Immobilizer Description and Operation

The immobilizer system functions are provided by the body control module (BCM) and the engine control module (ECM), as well as any modules which store and report the environment identifier. When ...

Key with Integrated Transmitter Programming

Keys can be programming in various ways using the procedures outlined below. Using the Replacing Keys procedures will first erase all the known keys from the vehicle. Any existing keys and any new ...

Other materials:

Liftgate Strut Replacement
Liftgate Strut Replacement Callout Component Name 1 Liftgate Strut Warning: When a lift gate hold open device is being removed or installed, provide alternate support to avoid the possibility of damage ...

Front Seat Cushion Outer Trim Panel Replacement
Front Seat Cushion Outer Trim Panel Replacement Callout Component Name Preliminary Procedures Remove the driver or passenger seat recliner handle. Refer to Front Seat Back Recliner Handle Replacement Remove the front seat ...

Hub/Axle Flange and Wheel Stud Runout Inspection
Special Tools GE-8001 Dial Indicator Set , or equivalent Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Mark the location of the wheels to the wheel studs and mark the specific vehicle position on each tire and wheel – LF, LR, RF, RR. Remove the tire and ...

0.0066