Chevrolet Sonic Repair Manual: Instrument Panel Accessory Bezel Package Installation

Installation Instructions Part Number

95205543

• Flat Bladed Plastic Trim Tool
• ?€?7, 10?€™mm Spanner
• Phillips Screw Driver
• T20 - Torx Driver

Instrument Panel Trim Removal Procedure

1. Using a flat bladed plastic trim tool, release the retainers securing the center molding?€‰(1) to the instrument panel assembly.


2. Using a flat bladed plastic trim tool, disengage the retainers securing the center upper trim molding?€‰(1) to the instrument panel assembly.
3. Disconnect electrical connections.



Note:

Steps 4 to 7 are for vehicles equipped with Automatic Transmission only.

4. Apply the parking brake.
5. Move the shifter from ?€?Park?€? to the ?€?Neutral?€? position.
6. Using a flat bladed plastic trim tool, release the retainers securing the console cover?€‰(1) to the console assembly.
7. Disconnect electrical connections.



Note:

Steps 8 to 11 are for vehicles equipped with Manual Transmission only.

8. Using a flat bladed plastic trim tool, release the retainers securing the console cover?€‰(1) to the console assembly.


9. Reach under the console cover assembly?€‰(1) and release the retainer tabs securing the transmission shift lever boot?€‰(2) to the console cover assembly.


10. Feed the transmission control lever boot assembly through the opening in the console cover assembly?€‰(1).
11. Remove the console cover assembly?€‰(1) from the vehicle.


12. Remove the heater and air conditioning control retainers?€‰(1).
13. Disconnect the electrical connectors from the switches.
14. Disconnect the heater and air conditioning temperature control cable.
15. Disconnect the mode control cable.
16. Disconnect the connectors of HVAC control ?€“ J1 (Blower), J2 (Main) and J3 (HVAC Module).
17. Remove the heater and air conditioning control from the HVAC bezel?€‰(2) by removing the four screws.
18. Remove the electrical switches from the HVAC bezel.

Instrument Panel Trim Installation Procedure

1. Install the heater and air conditioning control to the supplied HVAC bezel?€‰(2) by installing the four screws.

   Tighent

   
   Tighten the four screws to 5.5 Nm (49?€‰lb?€‰in).

2. Install the removed electrical switches to the supplied HVAC bezel.
3. Connect the connectors of HVAC control ?€“ J1 (Blower), J2 (Main) and J3 (HVAC Module).
4. Connect the mode control cable.
5. Connect the heater and air conditioning temperature control cable.
6. Connect the electrical switch connectors.
7. Install the HVAC control assembly with bezel?€‰(2) to the instrument panel and secure with the retainers?€‰(1).



Note:

Steps 7 to 10 are for vehicles equipped with Manual Transmission only.

8. Position the console cover assembly?€‰(1) to the console assembly.
9. Feed the transmission control lever boot assembly through the opening in the console cover assembly?€‰(1).


10. Snap the transmission control lever boot assembly?€‰(2) to the console cover?€‰(1) ensuring the retainer tabs lock the boot assembly to the cover.
11. Install the cover assembly to the vehicle.



Note:

Steps 11 and 12 are for vehicles equipped with Automatic Transmission only.

12. Connect the electrical connections.
13. Install the front floor console cover.


14. Connect the electrical connections to the supplied center upper trim molding?€‰(1).
15. Install the center upper trim molding to the instrument panel ensuring that the retainers are fully engaged.


16. Install the supplied center molding?€‰(1) to the instrument panel ensuring that the retainers are fully engaged.

Front Door Trim Removal Procedure

1. Using an appropriate plastic trim tool, remove the front side door upper front trim panel?€‰(1).


2. Remove the front side door inside handle bolt finish cap?€‰(1).
3. Remove the front side door inside handle fastener?€‰(2).
4. Remove the front side door trim fastener?€‰(3).
5. Use the appropriate plastic trim tool to aid in the removal of the front door trim?€‰(4).
6. Pull upwards on the door lock retainer cable to disengage.
7. Disconnect the electrical connector.


8. Remove the front side door window switch bezel screw?€‰(1) (Qty:8).
9. Remove the front side door window switch bezel assembly?€‰(2).


10. Disconnect the retainers and remove the front side door window switch assembly?€‰(1).
11. Disconnect the electrical connectors.


12. Remove the front side door window switch bezel bracket screws?€‰(1).
13. Remove the front side door window switch bezel brackets?€‰(2), (3).

    Note:

    Bezel brackets and screws are to be reused.

Front Door Trim Installation Procedure

1. Install the front side door window switch bezel brackets?€‰(2), (3) to the supplied front side door window switch bezel and secure with the screws?€‰(1).


2. Connect the electrical connectors.
3. Install the front side front door window switch assembly?€‰(1) to the supplied front side door window switch bezel.


4. Install the front side door window switch bezel assembly?€‰(2) to the front door trim panel.
5. Secure the front door window switch bezel assembly with the screws?€‰(1) (Qty:8).


6. Connect the electrical connections.
7. Install the front door trim panel?€‰(4) to the front door.
8. Install the front side door trim fastener?€‰(3).
9. Install the front side door inside handle fastener?€‰(2).
10. Install the front side door inside handle bolt finish cap?€‰(1).


11. Install the front side door upper front trim panel?€‰(1).

© 2014-2026 Copyright www.csmans.com

 
0.0051