Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Intake Manifold Replacement (LUW)

Chevrolet Sonic Repair Manual / Powertrain / Engine / Intake and Forced Induction / Intake Manifold / Intake Manifold Replacement (LUW)

Removal Procedure
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Remove the throttle body assembly. Refer to Throttle Body Assembly Replacement.


  3. Disconnect wiring harness plug.
  4. Disconnect the pipes from the evaporative emission canister purge solenoid valve (1).
  5. Remove the evaporative emission canister purge solenoid valve (1) and the rubber mounting from the intake manifold (2).
  6. Disconnect and reposition the electrical connectors as necessary.
  7. Remove the fuel injector rail. Refer to Fuel Injector Replacement.
  8. Remove the manifold absolute pressure sensor. Refer to Manifold Absolute Pressure Sensor Replacement.


  9. Disconnect the booster vacuum pipe (1) from the intake manifold.
  10. Remove the front wheel drive shaft right side. Refer to Front Wheel Drive Shaft Replacement.
  11. Remove the starter. Refer to Starter Replacement.
  12. Remove the generator. Refer to Generator Replacement.
  13. Remove the front exhaust pipe. Refer to Exhaust Front Pipe Replacement.


  14. Remove and DISCARD the transmission rear mount to bracket through bolt (1).

  15. Remove the intake manifold bolts (1).
  16. Remove the intake manifold (2).
  17. Clean and inspect the intake manifold. Refer to Intake Manifold Cleaning and Inspection.
Installation Procedure
  1. Clean the sealing surfaces.
  2. Install the NEW gasket.

    3. Caution:

    Refer to Fastener Caution.

  3. Install the intake manifold (2) and the 7 intake manifold bolts (1) and tighten to 20 Y (15 lb ft)

    .



  4. Install the NEW transmission rear mount to bracket through bolt (1) and tighten to 80 Y (59 lb ft) plus 45-60 degrees

    .

  5. Install the generator. Refer to Generator Replacement.
  6. Install the starter. Refer to Starter Replacement.
  7. Install the front exhaust pipe. Refer to Exhaust Front Pipe Replacement.
  8. Install the front wheel drive shaft right side. Refer to Front Wheel Drive Shaft Replacement.


  9. Connect the booster vacuum pipe (1) to the intake manifold.
  10. Install the manifold absolute pressure sensor. Refer to Manifold Absolute Pressure Sensor Replacement.
  11. Connect the electrical connectors as necessary.
  12. Install the fuel injector rail. Refer to Fuel Injector Replacement.


  13. Install the evaporative emission canister purge solenoid valve (1) and the rubber mounting to the intake manifold (2).
  14. Connect the pipes to the evaporative emission canister purge solenoid valve (1).
  15. Connect wiring harness as necessary.
  16. Install the throttle body assembly. Refer to Throttle Body Assembly Replacement.
  17. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
Intake Manifold Replacement (LDE)
Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. Remove the throttle body assembly. Refer to Throttle Body As ...

Intake Manifold Tuning Valve Actuator Replacement
Intake Manifold Tuning Valve Actuator Replacement Callout Component Name Preliminary Procedure Properly raise and support the v ...

Other materials:

Park Brake and P (Park) Mechanism Check
Warning: When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move. ...

Tire Terminology and Definitions
Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in kPa (kilopascal) or psi (pounds per square inch). Accessory Weight The combined weight of optional accessories. Some examples of optional access ...

Front Wheel Drive Shaft Replacement
Special Tools J-45859 Axle Remover For regional equivalent tools, refer to Special Tools. Removal Procedure Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the front suspension skid plate bolts (1) and the front suspen ...

В© 2014-2026 Copyright www.csmans.com
 
0.0053