Chevrolet Sonic manuals

Chevrolet Sonic Repair Manual: Low and Reverse and 1-2-3-4 Clutch Housing, and 1-2-3-4 Clutch Plate Installation (6T40/45/50)

Chevrolet Sonic Repair Manual / Powertrain / Transmission/Transaxle / Transmission Oil Cooler / Transmission Unit / Low and Reverse and 1-2-3-4 Clutch Housing, and 1-2-3-4 Clutch Plate Installation (6T40/45/50)



Low and Reverse and 1-2-3-4 Clutch Housing, and 1-2-3-4 Clutch Plate Installation

Callout

Component Name

1

Low and Reverse and 1??? Clutch Housing

Note:

The longer legs face the bottom of the case and the oil passages face the valve body end of the case.

2

Output Sun Gear Assembly

3

1??? Clutch Waved Plate

Note:

  • Align the single pair of tabs with the bottom valve body end of the case.
  • Ensure the correct waved plate is being installed. The 1??? clutch and low and reverse clutch waved plates are visually similar, however the low and reverse clutch waved plate is thicker.

4

1??? Clutch Plate (Qty: 2)

5

1??? Clutch Plate Assembly (Qty: 2)

6

1??? Clutch Backing Plate

Note:

Align the single skinny tab with the case spline facing the top of the case.

7

1??? Clutch Backing Plate Retainer Ring

Warning:

The retainer is under tension. Use care when removing or installing the retainer. Personal injury could result.

Caution:

Use caution during removal or installation of the retainer ring to avoid damage to the case machined surface in the park pawl area. Burrs or raised edges on the case machined surface can cause the park pawl to bind and prohibit it from engaging the park gear.

Note:

  • Install the retainer with the taper facing away from the backing plate.
  • Align the retainer opening with the largest gap in the case splines toward the bottom of the case.
  • Install one end of the retainer into the retainer ring groove. Use DT-28585 snap ring remover and work the retainer into the case groove. Use a screwdriver to hold the retainer away from the case while pushing down on the retainer with DT-28585 snap ring remover.

Special Tool

DT-28585 Snap Ring Remover or equivalent

For equivalent regional tools, refer to Special Tools.

Low and Reverse and 1-2-3-4 Clutch Housing, and 1-2-3-4 Clutch Plate Installation (6T30)
Low and Reverse and 1-2-3-4 Clutch Housing, and 1-2-3-4 Clutch Plate Installation Callout Component Name 1 Low and Re ...

Low and Reverse Clutch Assembly and Low and Reverse Clutch Plate Installation
Low and Reverse Clutch Assembly and Low and Reverse Clutch Plate Installation Callout Component Name 1 Low and Reverse C ...

Other materials:

Safety Belts
This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. Warning Do not let anyone ride where a safety belt cannot be worn properly. In a crash, if you or your passenger(s) are not wearing safety belts, injuries can be mu ...

Radiator Replacement (LDE LUW)
Radiator Replacement Callout Component Name Preliminary Procedures Drain the coolant. Refer to Cooling System Draining and Filling. Remove the engine coolant temperature sensor. Remove the air conditioning condenser. R ...

Generator Pulley Replacement (LUV)
Generator Pulley Replacement Callout Component Name Preliminary Procedure Remove the generator. Refer to Generator Replacement. 1 Generator Pulley Nut Cap 2 Generator Pul ...

В© 2014-2022 Copyright www.csmans.com
 
0.0073