Chevrolet Sonic Repair Manual: Low and Reverse and 1-2-3-4 Clutch Housing Assemble (6T30)
| Table 1: | 1??? Clutch Piston Installation |
| Table 2: | Low and Reverse Clutch Piston Installation |
- 1??? Clutch Piston Installation
1??? Clutch Piston Installation Callout
Component Name
1
1??? Clutch Piston
Note:
DT-48273 seal protector prevents the piston seal lip from damage during installation. Apply a thin coat of ATF to the I.D. of DT-48273 seal protector to ease the installation of the piston.
Special Tool
DT-48273 Seal Protector
For equivalent regional tools, refer to Special Tools.
2
1??? Clutch Spring
3
1??? Clutch Spring Retainer
Caution:
Regulate the air pressure to 276 kPa (40 psi) maximum. High pressure could cause the piston to over travel and damage the piston seals.
Note:
- Place the retainer onto DT-48274-1 which is part of DT-48274 spring installer. Compressing the spring using DT-48274-2 which is part of DT-48274 spring installer, will install the retainer into the retainer groove.
- Apply shop air to the clutch fluid feed hole in the clutch housing to verify proper piston operation.
Special Tool
DT-48274 Clutch Piston Spring Installer
For equivalent regional tools, refer to Special Tools.
- Low and Reverse Clutch Piston Installation
Low and Reverse Clutch Piston Installation Callout
Component Name
1
Low and Reverse Clutch Piston
Note:
DT-48273 seal protector prevents the piston seal lip from damage during installation. Apply a thin coat of ATF to the I.D. of DT-48273 seal protector to ease the installation of the piston.
Special Tool
DT-48273 Clutch Piston Seal Protector
For equivalent regional tools, refer to Special Tools.
2
Low and Reverse Clutch Spring
3
Low and Reverse Clutch Spring Retainer
Caution:
Regulate the air pressure to 276 kPa (40 psi) maximum. High pressure could cause the piston to over travel and damage the piston seals.
Note:
- Place the retainer onto DT-48274-1 which is part of DT-48274 spring installer. Compressing the spring using DT-48274-2 which is part of DT-48274 spring installer, will install the retainer into the retainer groove.
- Apply shop air to the clutch fluid feed hole in the clutch housing to verify proper piston operation.
Special Tool
DT-48274 Spring Installer
For equivalent regional tools, refer to Special Tools.
Torque Converter Housing with Fluid Pump Assembly Removal (Non Hybrid)
Torque Converter Housing with Fluid Pump Assembly Removal
Callout
Component Name
1
Torque Converter and Differential Hou ...
Low and Reverse and 1-2-3-4 Clutch Housing Assemble (6T40/45/50)
Table 1:
1??? Clutch Piston Installation
Table 2:
Low and Reverse Clutch Piston Installation
1??? Clutch Piston Installation
1??? Clutch Piston Installa ...
Other materials:
Door Lock and Ignition Lock Folding and Non-Folding Key Cutting
High Security keys are available from the service parts system.
Obtain the key code from the security card or from the GM Dealer World, Parts,
Key Code Look Up system.
If you have the key code and access to a Triax-E., BD Laser or other code key
cutting machine from the GM Dealer Equipment C ...
Instrument Panel Compartment Door Dampener Replacement
Instrument Panel Compartment Door Dampener Replacement
Callout
Component Name
Preliminary Procedure
Remove the instrument panel lower compartment. Refer to Instrument Panel
Lower Compartment Replacement.
1 ...
Starter Replacement (LUV)
Removal Procedure
Disconnect the battery negative cable. Refer to Battery Negative Cable
Disconnection and Connection.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
If equipped with a front suspension skid plate, remove the drivetrain
...
0.0071