Chevrolet Sonic Repair Manual: Low and Reverse and 1-2-3-4 Clutch Housing Assemble (6T40/45/50)
| Table 1: | 1??? Clutch Piston Installation |
| Table 2: | Low and Reverse Clutch Piston Installation |
- 1??? Clutch Piston Installation
1??? Clutch Piston Installation Callout
Component Name
1
1??? Clutch Piston
Note:
DT-47798 seal protector prevents the piston seal lip from damage during installation. Apply a thin coat of ATF to the I.D. of DT-47798 seal protector to ease the installation of the piston.
Special Tool
DT-47798 Seal Protector
For equivalent regional tools, refer to Special Tools.
2
1??? Clutch Spring
3
1??? Clutch Spring Retainer
Caution:
Regulate the air pressure to 276 kPa (40 psi) maximum. High pressure could cause the piston to over travel and damage the piston seals.
Note:
- Place the retainer onto DT-47799-1 which is part of DT-47799 spring compressor. Compressing the spring using DT-47799-2 which is part of DT-47799 spring compressor, will install the retainer into the retainer groove.
- Apply shop air to the clutch fluid feed hole in the clutch housing to verify proper piston operation.
Special Tool
DT-47799 Clutch Piston Spring Compressor
For equivalent regional tools, refer to Special Tools.
- Low and Reverse Clutch Piston Installation
Low and Reverse Clutch Piston Installation Callout
Component Name
1
Low and Reverse Clutch Piston
Note:
DT-47807 seal protector prevents the piston seal lip from damage during installation. Apply a thin coat of ATF to the I.D. of DT-47807 seal protector to ease the installation of the piston.
Special Tool
DT-47807 Clutch Piston Seal Protector
For equivalent regional tools, refer to Special Tools.
2
Low and Reverse Clutch Spring
3
Low and Reverse Clutch Spring Retainer
Caution:
Regulate the air pressure to 276 kPa (40 psi) maximum. High pressure could cause the piston to over travel and damage the piston seals.
Note:
- Place the retainer onto DT-47794-1 which is part of DT-47794 spring compressor. Compressing the spring using DT-47794-2 which is part of DT-47794 spring compressor, will install the retainer into the retainer groove.
- Apply shop air to the clutch fluid feed hole in the clutch housing to verify proper piston operation.
Special Tool
DT-47794 Spring Compressor
For equivalent regional tools, refer to Special Tools.
Low and Reverse and 1-2-3-4 Clutch Housing Assemble (6T30)
Table 1:
1??? Clutch Piston Installation
Table 2:
Low and Reverse Clutch Piston Installation
1??? Clutch Piston Installation
1??? Clutch Piston Installa ...
Low and Reverse and 1-2-3-4 Clutch Housing Cleaning and Inspection
Low and Reverse and 1-2-3-4 Clutch Housing Cleaning and Inspection
Callout
Component Name
Caution: After cleaning the transmis ...
Other materials:
Rear Brake Hose Replacement (Body to Axle - Disc Brake)
Removal Procedure
Warning: Refer to Brake Dust Warning.
Warning: Refer to Brake Fluid Irritant Warning.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
Remove the tire and wheel assembly. Refer to Tire and Wheel Removal
and Install ...
General Description
The factory installed tires are designed to operate satisfactorily with loads
up to and including the full rated load capacity when these tires are inflated to
the recommended pressures.
The following factors have an important influence on tire life:
Correct tire pressures
Correct wheel ...
Relay Replacement (Within an Electrical Center)
Special Tools
EL-43244 Relay Puller Pliers
Removal Procedure
Remove the electrical center cover.
Note:
Always note the orientation of the relay.
If equipped with a notch style relay; observe the location of
the notch on the old relay to verify the new r ...
0.0074