Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Oil Pan Replacement

Chevrolet Sonic Repair Manual / Powertrain / Engine / Engine Lubrication / Oil Sump/Pan / Oil Pan Replacement

Special Tools

EN-49980 Guidance Pins

For equivalent regional tools, refer to Special Tools.

Removal Procedure
  1. Remove the right front wheelhouse liner extension. Refer to Front Wheelhouse Liner Inner Front Extension Replacement.
  2. Remove the oil filter and drain the engine oil. Refer to Engine Oil and Oil Filter Replacement.
  3. Remove the front insulator cover. Refer to Front Compartment Front Insulator Cover Replacement.
  4. Remove the front exhaust pipe. Refer to Exhaust Front Pipe Replacement.


    5. Note:

    The intermediate shaft is shown removed for visual purposes only.

  5. If equipped with an automatic transmission, remove the oil pan to automatic transmission bolts (1, 3) and automatic transmission converter cover (2).

  6. Remove the oil pan to automatic transmission bolts (1) .

  7. If equipped with manual transmission, remove the 3 manual transmission to oil pan bolts (1).

  8. Remove the oil pan bolts (1) and oil pan.
Installation Procedure
  1. Clean the sealing surface of crankshaft bearing cap tie plate and the groove in the engine front cover from old gasket material, oil, dirt and grease.

  2. Install the 2 EN-49980 guidance pins (1) to the shown oil pan screw bores.


    3. Note:

    The sealing bead should be applied close to the inner edge of the oil pan. Take care that the oil suction gallery (4) will not get contaminated with sealing compound or dirt.

  3. Apply 2 mm (0.0787 in)

    thickness of sealing compound (3, 2, 1).



    4. Caution:

    Refer to Fastener Caution.

    Note:

    The complete installation procedure of the oil pan should be done in 10 minutes.

  4. Loosely install the oil pan bolts (1) in all but the guidance pin locations.
  5. Remove the EN-49980 guidance pins and install the remaining oil pan bolts.
  6. Tighten the oil pan bolts to 10 Y (89 lb in)

    .



  7. If equipped with manual transmission, install the 3 manual transmission to oil pan bolts (1) and tighten to 40 Y (30 lb ft)

    .



  8. If equipped with an automatic transmission, install and the automatic transmission converter cover (2) and tighten the cover to automatic transmission bolt (1) to 40 Y (30 lb ft)

    and automatic transmission bolt (3) to 60 Y (44 lb ft)

    .



  9. Install the oil pan to automatic transmission bolts (1), and tighten to 40 Y (30 lb ft)

    .

  10. Install a NEW oil filter and fill the engine with oil. Refer to Engine Oil and Oil Filter Replacement.
  11. Install the exhaust pipe. Refer to Exhaust Front Pipe Replacement.
  12. Install the front insulator cover. Refer to Front Compartment Front Insulator Cover Replacement.
  13. Install the right front wheelhouse liner extension. Refer to Front Wheelhouse Liner Inner Front Extension Replacement.
Oil Pan Removal
Remove the 16 oil pan bolts (1). Caution: Pry the oil pan carefully in order to prevent damage to the transaxle case or the oil pan sealing surfaces. Place a ...

Pulleys and Belts
...

Other materials:

Reduced Engine Power Light
The reduced engine power light should come on briefly as the engine is started. If it does not come on, have the vehicle serviced by your dealer. This light, along with the malfunction indicator lamp, displays when a noticeable reduction in the vehicle's performance occurs. The vehicle c ...

Special Tools
Illustration Tool Number/ Description EL 35616-F J 35616 Terminal Test Kit ...

Meters and gauges
Example The Nissan Armada instrument cluster provides clear and precise vehicle data, allowing drivers to monitor performance, efficiency, and safety indicators in real time. This ensures confident driving in all conditions. Tachometer Drive Mode Selector indicator* Automatic Transm ...

В© 2014-2026 Copyright www.csmans.com
 
0.0067