Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Rear Brake Caliper Bracket Replacement

Chevrolet Sonic Repair Manual / Chassis / Brakes / Disc Brakes / Brake Calipers / Rear Brake Caliper Bracket Replacement

Removal Procedure

Warning:

Refer to Brake Dust Warning.

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.


    3. Note:

    • DO NOT use any air tools to remove or install the guide pin bolts. Use hand tools ONLY.
    • Install an open end wrench to hold the caliper guide pin in line with the brake caliper while removing or installing the caliper guide pin bolt. DO NOT allow the open end wrench to come in contact with the brake caliper. Allowing the open end wrench to come in contact with the brake caliper will cause a pulsation when the brakes are applied.
  3. Using a backup wrench to hold the brake caliper guide pins stationary, remove the brake caliper guide pin bolts (1).

    4. Caution:

    Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

  4. Remove the brake caliper and support with heavy mechanics wire.

  5. Remove the outer disc brake pad (1).
  6. Remove the inner disc brake pad (2).

  7. Remove the disc brake pad springs (1).

  8. Remove the upper brake caliper guide pin (1).

    9. Note:

    The lower brake caliper guide pin is equipped with a bushing and must be installed in the same location.

  9. Remove the lower brake caliper guide pin (2).

  10. Remove the brake caliper guide pin seals (1).

    11. Note:

    Do not reuse the brake caliper bracket bolts.

  11. Remove and discard the brake caliper bracket bolts (1).
  12. Remove the rear brake caliper bracket.
Installation Procedure
  1. Install the rear brake caliper bracket.

    2. Caution:

    Refer to Fastener Caution.

  2. Install new brake caliper bracket bolts (1) and tighten to 100 Y (74 lb ft)

    .



    3. Note:

    Ensure the brake caliper guide pin seals are fully seated in the groove of the brake caliper bracket.

  3. Install the brake caliper guide pin seals (1).

  4. Install the upper brake caliper guide pin (1).

    5. Note:

    The lower brake caliper guide pin is equipped with a bushing and must be installed in the same location.

  5. Install the lower brake caliper guide pin (2).

  6. Install the disc brake pad springs (1).

  7. Install the outer disc brake pad (1).
  8. Install the inner disc brake pad (2).
  9. Position the brake caliper over the disc brake pads and to the brake caliper bracket.

  10. Using a backup wrench to hold the brake caliper guide pins stationary, install the brake caliper guide pin bolts (1) and tighten to 28 Y (21 lb ft)

    .

  11. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
Front Seat Belt Anchor Plate Tensioner Replacement
Front Seat Belt Anchor Plate Tensioner Replacement Callout Component Name Warning: Refer to SIR Warning. Warning: ...

Rear Brake Caliper Replacement
Removal Procedure Warning: Refer to Brake Dust Warning. Warning: Refer to Brake Fluid Irritant Warning. Raise and support the vehicle. Refer to Lifting and Jacking the ...

Other materials:

Infotainment
Determine which radio the vehicle has and read the following pages to become familiar with its features. Warning Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to infotainment tasks while dr ...

Brake System Warning Light
The vehicle brake system consists of two hydraulic circuits. If one circuit is not working, the remaining circuit can still work to stop the vehicle. For normal braking performance, both circuits need to be working If the warning light comes on, there is a brake problem. Have the brake system ...

Tire Pressure Monitor Operation
This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in ...

В© 2014-2026 Copyright www.csmans.com
 
0.0058