Chevrolet Sonic manuals

Chevrolet Sonic Repair Manual: Rear Side Door Outer Panel Replacement

Chevrolet Sonic Repair Manual / Body / Doors and Enclosures / Doors / Rear Side Door Outer Panel Replacement

Removal Procedure

    Warning:

    Refer to Glass and Sheet Metal Handling Warning.

    Note:

    According to different corrosion warranties, only the regional mandatory joining methods are allowed.

  1. Disable the SIR System. Refer to SIR Disabling and Enabling.
  2. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  3. Remove the rear side door. Refer to Rear Side Door Replacement.
  4. Remove the rear side door outside handle. Refer to Rear Side Door Outside Handle Replacement.
  5. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.


  6. Grind the edges of the rear side door outer panel (1) to separate the outer door panel from the door shell.

  7. Warning:

    Inspection of the door guard beam for damage must be performed before replacement of the door outer panel. If damage to the door guard beam is found the door must be replaced. Failure to do so may compromise the structural integrity of the vehicle and may cause personal injury if the vehicle is involved in a collision.

  8. Remove the rear side door outer door panel (1).
  9. Remove the sealers and anti-corrosion materials from the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
  10. Straighten the edges of the door shell.
Installation Procedure
  1. Align the rear side door outer panel.
  2. Verify the fit of the rear side door outer panel.

  3. Clamp the rear side door outer panel (1) into position.

  4. Continue to hammer in stages along the hem flanges (1).
  5. Apply the sealers and anti-corrosion materials to the repair area, as necessary. Refer to Anti-Corrosion Treatment and Repair.
  6. Install the rear side door outside handle. Refer to Rear Side Door Outside Handle Replacement.
  7. Install the rear side door. Refer to Rear Side Door Replacement.
  8. Paint the repaired area. Refer to Basecoat/Clearcoat Paint Systems.
  9. Install all related panels and components.
  10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  11. Enable the SIR system. Refer to SIR Disabling and Enabling.
Rear Side Door Opening Floor Carpet Retainer Replacement
Rear Side Door Opening Floor Carpet Retainer Replacement Callout Component Name Preliminary Procedure Remove the rear seat cush ...

Rear Side Door Replacement
Rear Side Door Replacement Callout Component Name Warning: Refer to SIR Warning. Preliminary Procedures Mark the l ...

Other materials:

Tire Pressure Indicator Sensor Learn
Special Tools EL-46079 Tire Pressure Monitor Diagnostic Tool EL-50448 Tire Pressure Monitor Sensor Activation Tool For equivalent regional tools, refer to Special Tools. Learn Mode Description The tire pressure monitor system uses the instrument cluster, body control module ...

Lift Plate and Holding Fixture Installation
Lift Plate and Holding Fixture Installation Callout Component Name 1 DT-47811-A Transmission Lift Plate Warning: Handle with care, the transmission assembly weighs over 83 Kg (183 lbs). Bodily i ...

Low and Reverse and 1-2-3-4 Clutch Housing, Low and Reverse Clutch Assembly, Output Sun Gear, and 2-6 Clutch Plate Disassemble (Gen 1)
Low and Reverse and 1-2-3-4 Clutch Housing, Low and Reverse Clutch Assembly, Output Sun Gear, and 2-6 Clutch Plate Disassemble Callout Component Name 1 1??? Clutch Backing Plate 2 1??? Clu ...

В© 2014-2024 Copyright www.csmans.com
 
0.0061