Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Rear Wheel Bearing and Hub Replacement (Disc Brake)

Chevrolet Sonic Repair Manual / Chassis / Suspension / Rear Wheel Bearing and Hub Replacement (Disc Brake)

Special Tools

EN–45059 Angle Meter

For equivalent regional tools, refer to Special Tools.

Removal Procedure
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle.
  2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.

    Caution:

    Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

  3. Without disconnecting the hydraulic brake flex hose, remove and support the rear brake caliper and bracket as an assembly. Refer to Rear Brake Caliper Replacement.
  4. Remove the rear brake rotor. Refer to Rear Brake Rotor Replacement.


  5. Remove the wheel speed sensor bolt (1).
  6. Remove the wheel speed sensor (2).

  7. Remove and DISCARD the 4 wheel bearing/hub mounting bolts (1).

  8. Remove the wheel bearing/hub assembly (2) and rear brake shield (1) from the rear axle.
Installation Procedure

    Position the rear brake shield (1) and wheel bearing/hub assembly (2)
  1. Position the rear brake shield (1) and wheel bearing/hub assembly (2) in the rear axle.

    2. Caution:

    Refer to Fastener Caution.

  2. Install the 4 NEW wheel bearing/hub mounting bolts (1) and tighten a first pass to 58 Y (43 lb ft)

    . Tighten the bolts evenly, in a cross-pattern.



  3. Install the wheel speed sensor (2).
  4. Install the wheel speed sensor bolt (1) and tighten to 6 Y (53 lb in)

    .

  5. Install the brake rotor. Refer to Rear Brake Rotor Replacement.
  6. Install the brake caliper and bracket as an assembly. Refer to Rear Brake Caliper Replacement.
  7. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation.
  8. Lower the vehicle.
Front Wheel Bearing and Hub Replacement
Special Tools CH-50559 Wheel Hub/Bearing Remover Kit For equivalent regional tools, refer to Special Tools. Removal Procedure Raise and support the vehicle. Refer to Lifting and Jac ...

Rear Wheel Bearing and Hub Replacement (Drum Brake)
Rear Wheel Bearing and Hub Replacement Callout Component Name Preliminary Procedures Raise and support the vehicle. Refer to Liftin ...

Other materials:

License Plate Lamp
Lamp Assembly Bulb Assembly 1. Bulb Socket 2. Bulb 3. Lamp Assembly To replace one of these bulbs: 1. Push the left end of the lamp assembly toward the right. 2. Turn the lamp assembly down to remove it. 3. Turn the bulb socket (1) counterclockwise to remove it from the lamp assembly ( ...

Tire and Wheel Removal and Installation
Special Tools CH-41013 Rotor Resurfacing Kit CH-42450-A Wheel Hub Resurfacing Kit For equivalent regional tools, refer to Special Tools. Removal Procedure Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the wheel cover ...

System temporarily unavailable
In the Nissan Armada, if the Blind Spot Warning (BSW) system detects that the radar sensors are obstructed, the system will automatically deactivate and display the message "Unavailable Side Radar Obstruction" in the vehicle information display. The Nissan Armada BSW system will remai ...

© 2014-2026 Copyright www.csmans.com
 
0.0058