Chevrolet Sonic Repair Manual: Rear Window Replacement
Special Tools
- BO-24402-A Glass Sealant Remover (Cold Knife)
- BO-39032 Stationary Glass Removal Tool
- Use an adhesive that is approved by GM
For equivalent regional tools, refer to Special Tools
- Removal Procedure
-
- Open the rear compartment lid.
- Disconnect the rear window defogger electrical connectors.
- Disconnect the OnStar?® antenna, if equipped.
- Disconnect the rear window radio antenna connector.
- Cover to protect the following parts from broken glass:
Warning:
If a window is cracked but still intact, crisscross the window with masking tape in order to reduce the risk of damage or personal injury.
Note:
Before cutting out a stationary window, apply a double layer of masking tape around the perimeter of the painted surfaces and inner trim.
Warning:
If broken glass falls into the defroster outlets, it can be blown into the passenger compartment and cause personal injury.
- Upper dash pad
- Defroster outlets and A/C outlets
- Seats and carpeting
Note:
Keep the cutting edge of the appropriate tool against the window. There are window locating pins, one in each upper corner of the window. Use care Not to remove or cut them off when removing the window. If the window locator pins are cut, it will be necessary to tape the window in place.
- This will allow the auto-adhesive to be separated from the window.
- Remove the rear window reveal molding. Refer to Rear Window Reveal Molding Replacement.
- Leave a base of urethane on the pinchweld flange.
- The only suitable lubrication is clear water.
- The only suitable lubrication is clear water.
- BO-24402-A Glass Sealant Remover (Cold Knife).
- BO-39032 Stationary Glass Removal Tool.
- Use the appropriate tool to remove the bottom of the window from the auto-adhesive. Keep the cutting edge of the tool against the window. Do this from inside the vehicle.
- With an assistant, remove the window?€‰(2) from the vehicle. Check that the retainers?€‰(1) are still attached to the window before installing.
- Installation Procedure
-
- Install the rear window into the opening. Refer to Adhesive Installation of Rear Windows.
- Connect the rear window defogger electrical connectors.
- Install the rear window radio antenna connector.
- Connect the OnStar?® antenna, if equipped.
Check the radio and OnStar?® system to verify reception.
- Close the rear compartment lid.
- Remove the double layer of masking tape around the perimeter of the painted surfaces and the interior trim.
Rear Window Panel Trim Replacement
Rear Window Panel Trim Replacement
Callout
Component Name
Preliminary Procedures
Remove the body lock pillar upper trim panel. Refe ...
Rear Window Reveal Molding Replacement
Rear Window Reveal Molding Replacement
Callout
Component Name
Preliminary Procedures
Remove the rear window to replace the reve ...
Other materials:
Starting Procedure
1. With your foot off the accelerator pedal, turn the ignition to START. When
the engine cranks, let go of the key. The idle speed will go down as the engine
gets warm.
The vehicle has a Computer-Controlled Cranking System. It assists in starting
the engine and protects components. If the ign ...
Cylinder Head Disassemble
Special Tools
EN-840 Pliers/Remover
EN-8062 Valve Spring Compressor
EN-8062-5 Adapter
EN-50717-2 Compressor Assembly of EN-50717 Kit
For equivalent regional tools, refer to Special Tools.
Install the EN-50717?E assembly (1) to the EN-8062 compressor
(4).
Install the E ...
Oil Pan Cleaning and Inspection
Warning: Wear safety glasses when using compressed air in order
to prevent eye injury.
Caution: To ensure proper engine lubrication, clean clogged or
contaminated oil galleries in an approved solvent and with compressed air.
Failure to clean oil galleries may cause ...
0.01