Illustration |
Tool Number/Description |
---|---|
|
207649 Rod Hairpins |
|
547324 Flange Screws |
|
EN-232 KM-232 J-21867-L40 Oil Pressure Check Adapter |
|
EN-235-6 KM-235-6 Installer |
|
EN-328–B GE-328-B KM-328-B GE-6125-1B Remover |
|
EN-422 KM-422 83 94 959 Installer |
|
EN-498–B GE-21867-A J-21867-A KM-498-B CH-48027 Pressure Gauge and Adapter Set |
|
EN-652 KM-652 Flywheel Holder |
|
EN-658-1 KM-658-1 J-35264 Installer |
|
EN-796 KM-796-A Dismantler |
|
CH-807 KM-807 Closure Plugs |
|
EN-840 KM-840 J-36017 83 94 157 Remover |
|
EN-845 KM-845 Suction Device |
|
EN-849 KM-849 Assembly Tray |
|
EN-958 KM-958 Valve Stem Seal Installer |
|
EN-6009 KM-6009 83 96 335 J-43301 Remover/Installer |
|
EN-6333 KM-6333 Locking Pin |
|
EN-6340 KM-6340 Locking Tool |
|
EN-6349 KM-6349 Locking Pin |
|
EN-6351 KM-6351 Assembly Sleeves |
|
EN-6361 KM-6361 Feeler Gauge Set |
|
EN-6624 KM-6624 Remover |
|
EN-6625 KM-6625 Flywheel Locking Device |
|
EN-6628-A KM-6628-A Locking Tool |
|
EN-8087 J-8087 Cylinder Bore Gauge |
|
EN-28467-B J-28467-B Universal Engine Support Fixture |
|
EN-34730-91 KM-34730-91 Pressure Tester |
|
EN-36857 J-36857 Engine Lift Bracket |
|
EN-43405 J-43405 Support Foot Set |
|
EN-45000 KM-45000 J-45000 Seal Remover |
|
EN-45059 J-45059 Angle Meter |
|
GE-571-B MKM-571-B GE-8001 J-8001 Dial Gauge |
|
GE-22738-B J-22738-B Valve Spring Tester |
|
J-37088-A KM-37088A Fuel Line Disconnect Tool Set |
|
EN-50717-1 Stands |
|
EN-50717-2 Compressor |
|
EN-8062 J-8062 Valve Spring Compressor |
Rear Side Door Window Switch Bezel Replacement
Rear Side Door Window Switch Bezel Replacement
Callout
Component Name
Preliminary Procedure
Remove the rear side door trim. Refer to Rear Side Door Trim Replacement.
1
Rear Side Door Pull Handle ...
Electronic Brake Control Module Programming and Setup
Note:
DO NOT program a control module unless directed to by a service procedure
or a service bulletin. If the ECU is not properly configured with the correct
calibration software, the ECU will not control all of the vehicle features
properly.
Ensure the programming tool is ...
Tire Dismounting and Mounting (Lubricant)
Important:
Lubricant should be applied to form a thin, just visible layer,
on the bead foot and bead outer areas. There should not be any visible
clumps of lubricant.
Never use soap or any lubricant net specifically designed for tire
assembly.
Lubricant ...