Chevrolet Sonic manuals

Chevrolet Sonic Repair Manual: Tire Dismounting and Mounting

Chevrolet Sonic Repair Manual / Chassis / Wheels/Tires / Wheels / Tire Dismounting and Mounting

Caution:

Use a tire changing machine in order to dismount tires. Do not use hand tools or tire irons alone in order to remove the tire from the wheel. Damage to the tire beads or the wheel rim could result.

Caution:

Do not scratch or damage the clear coating on aluminum wheels with the tire changing equipment. Scratching the clear coating could cause the aluminum wheel to corrode and the clear coating to peel from the wheel.

    Caution:

    Damage to either the tire bead or the wheel mounting holes can result from the use of improper wheel attachment or tire mounting procedures. It takes up to 70 seconds for all of the air to completely exhaust from a large tire. Failure to follow the proper procedures could cause the tire changer to put enough force on the tire to bend the wheel at the mounting surface. Such damage may result in vibration and/or shimmy, and under severe usage lead to wheel cracking.

  1. Deflate the tire completely.
  2. Note:

    Rim-clamp, sometimes called-European-type tire changers are recommended.

  3. Use the tire changer in order to remove the tire from the wheel.
  4. Use a wire brush or coarse steel wool in order to remove any rubber, light rust or corrosion from the wheel bead seats.
  5. Caution:

    When mounting the tires, use an approved tire mounting lubricant. DO NOT use silicon or corrosive base compounds to lubricate the tire bead and the wheel rim. A silicon base compound can cause the tire to slip on the rim. A corrosive type compound can cause tire or rim deterioration.

  6. Apply GM P/N 12345884 (Canadian P/N 5728223) or equivalent to the tire bead and the wheel rim.
  7. Use the tire changer in order to install the tire to the wheel.
  8. Warning:

    To avoid serious personal injury, do not stand over tire when inflating. The bead may break when the bead snaps over the safety hump. Do not exceed 275 kPa (40 psi) pressure when inflating any tire if beads are not seated. If 275 kPa (40 psi) pressure will not seat the beads, deflate, relubricate the beads and reinflate. Overinflation may cause the bead to break and cause serious personal injury.

  9. Inflate the tire to the proper air pressure.
  10. Ensure that the locating rings are visible on both sides of the tire in order to verify that the tire bead is fully seated on the wheel.
Thrust Angles Description
The front wheels aim or steer the vehicle. The rear wheels control tracking. This tracking action relates to the thrust angle (3). The thrust angle is the path that the rear wheels take. ...

Tire Dismounting and Mounting (Bead Exercising)
Most effective if done within 5 minutes of lube application. Tire exercising is required for all tires and should be done prior to balancing and checking for RFV. Lack of bead exercising w ...

Other materials:

Seat Adjustment
Manual Seats To adjust a manual seat: 1. Pull the handle at the front of the seat. 2. Slide the seat to the desired position and release the handle. 3. Try to move the seat back and forth to be sure it is locked in place. See Seat Adjustment. Seat Height Adjuster If available, move the le ...

Storing an SiriusXM Channel
Drivers are encouraged to set up XM channel favorites while the vehicle is not moving. Tune to favorite stations using the pushbuttons, favorites button, and steering wheel controls. See Defensive Driving. A maximum of 36 stations can be programmed as favorites using the six pushbuttons posit ...

Low and Reverse Clutch Assembly and Low and Reverse Clutch Plate Installation
Low and Reverse Clutch Assembly and Low and Reverse Clutch Plate Installation Callout Component Name 1 Low and Reverse Clutch Assembly (OWC) Note: The Low and Reverse Clutch Assembly should rotat ...

В© 2014-2024 Copyright www.csmans.com
 
0.0095