Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Tire Pressure Indicator Sensor Replacement

Chevrolet Sonic Repair Manual / Accessories / Storage / Tire Pressure Indicator Sensor Replacement

Removal Procedure
  1. Raise the vehicle on a suitable support. Refer to Lifting and Jacking the Vehicle.
  2. Remove the tire/wheel assembly from the vehicle. Refer to Tire and Wheel Removal and Installation.
  3. Dismount the tire from the rim. Refer to Tire Dismounting and Mounting.


    4. Note:

    When servicing the tire pressure sensor always use a new Schrader® tire pressure monitoring (TPM) sensor and a new TORX screw during installation.

  4. Remove the TORX screw (1) from the tire pressure sensor (2) and pull it straight off the tire pressure valve stem (3).

    5. Caution:

    Do not scratch or damage the clear coating on aluminum wheels with the tire changing equipment. Scratching the clear coating could cause the aluminum wheel to corrode and the clear coating to peel from the wheel.

  5. Remove the tire pressure valve stem by pulling it through the rim.
Installation Procedure


    Caution:

    Refer to Fastener Caution.

    Note:

    • Ensure the flat of the valve, lines up with the flats of the snap in the enclosure.
    • TPM valves and TORX screws are single use items.
  1. Assemble the tire pressure sensor (2) to the valve stem and install the new TORX screw (3), tighten to 1.3 Y (11.5 lb in)

    .

    2. Note:

    Use an approved tire mounting lubricant. DO NOT use silicon or corrosive base compounds to lubricate the tire bead and the wheel rim. A corrosive type compound can cause tire or rim deterioration.

  2. Apply tire soap to the rubber portion of the valve stem (1).

  3. Using a tire valve stem mounting tool, pull the valve stem through in a direction parallel to the valve hole on the rim.

    4. Note:

    Snap Fit TPM sensors are shipped in the OFF mode. The sensor will exit its OFF state when the tire is inflated.

  4. Mount the tire to the rim. Refer to Tire Dismounting and Mounting.
  5. Install the tire/wheel assembly on the vehicle. Refer to Tire and Wheel Removal and Installation.
  6. Lower the vehicle.
  7. Learn the tire pressure sensors. Refer to Tire Pressure Indicator Sensor Learn.
Tire Pressure Indicator Sensor Learn
Special Tools EL-46079 Tire Pressure Monitor Diagnostic Tool EL-50448 Tire Pressure Monitor Sensor Activation Tool For equivalent regional tools, refer to Special Tools. Learn Mode Desc ...

Transmission Indicators and Messages
The following transmission-related indicators and messages may be displayed on the Instrument Panel Cluster (IPC). For a complete listing and description of all vehicle indicators and messag ...

Other materials:

Instrument Panel Outer Air Outlet Duct Replacement
Instrument Panel Outer Air Outlet Duct Replacement Callout Component Name Preliminary Procedures Remove the instrument panel assembly. Refer to Instrument Panel Assembly Replacement. Reposition any wiring or hoses to gain ...

Reverse (Gen 1)
When the gear selector lever is moved to the Reverse (R) position (from the Park position) the normally-high 35R pressure control solenoid 2 is commanded ON and the following changes occur in the transmission? hydraulic and electrical systems: 3-5-Reverse Clutch Applies Manual Valv ...

Clutch and Differential Housing Disassemble
Special Tools M-680770 Universal Sliding Mallet R-0007758 Holding Fixture R-0407008 Counter Shaft Bearing Remover R-0407010 Input Shaft Needle Bearing Puller and Driver R-0407013 Gearshift Device Bushing Puller R-0007761 Universal Handle for Pullers and Installers T-0207928 Retai ...

© 2014-2026 Copyright www.csmans.com
 
0.009