Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Transmission Fluid Drain and Fill

Chevrolet Sonic Repair Manual / Powertrain / Transmission/Transaxle / Manual / General / Transmission Fluid Drain and Fill

Draining Procedure

Note:

  • The fluid check bolt at the front of the transmission may not be opened.
  • The transmission fluid drained out during the pre-delivery inspection may be re-used. New transmission fluid must be used during servicing work.

    The transmission fluid must be brought up to operating temperature before draining.

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  2. Remove the drivetrain and front suspension frame skid plate, if equipped. Refer to Drivetrain and Front Suspension Frame Skid Plate Replacement.


  3. Clean away all dirt and debris from the transmission fluid drain fastener area.
  4. Position an appropriate container under the transmission.
  5. Remove the transmission fluid drain fastener (1).
  6. Allow the transmission fluid to drain into the container.

    7. Caution:

    Refer to Fastener Caution.

  7. Install a new transmission fluid drain fastener and tighten to 20 Y (15 lb ft)

    .

  8. Remove the container used to catch the used transmission fluid from under the vehicle.
  9. Install the drivetrain and front suspension frame skid plate, if equipped. Refer to Drivetrain and Front Suspension Frame Skid Plate Replacement.
Filling Procedure

    Lower the vehicle.
  1. Lower the vehicle.
  2. Remove the engine control module with the bracket from the battery tray. Refer to Engine Control Module Replacement for the 1.2L or 1.4L engine, or Engine Control Module Replacement for the 1.6L or 1.8L engine.
  3. Clean away all dirt and debris from the transmission fluid fill fastener area.
  4. Remove the transmission fluid fill fastener (1).
  5. Fill the transmission with the appropriate amount of fluid. Refer to Fluid and Lubricant Recommendations and Manual Transmission Specifications.
  6. Install a new transmission fluid fill fastener and tighten to 30 Y (22 lb ft)

    .

  7. Install the engine control module with the bracket to the battery tray. Refer to Engine Control Module Replacement for the 1.2L or 1.4L engine, or Engine Control Module Replacement for the 1.6L or 1.8L engine.
Transmission Disassemble (Gen 2)
Special Tools 3-9506289 Universal Adapter R-0007758 Holding Fixture S-9407198 Differential Bearing Race Wrench For equivalent regional tools, refer to Special Tools. Attach R-0 ...

Transmission Fluid Level and Condition Check
Removal Procedure Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle Remove the front suspension skid plate, if equipped. Refer to Drivetrain and Front Sus ...

Other materials:

Tire Inspection
We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: The indicators at three or more places around the tire can be seen. There is cord or fabric showing through the tire's rubb ...

Hub/Axle Flange and Wheel Stud Runout Inspection
Special Tools GE-8001 Dial Indicator Set , or equivalent Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Mark the location of the wheels to the wheel studs and mark the specific vehicle position on each tire and wheel – LF, LR, RF, RR. Remove the tire and ...

Engine Coolant Fan Replacement (LDE/LUW)
Removal Procedure Unclip transmission cooler lines from shroud if equipped. Unclip radiator surge tank outlet hose from fan shroud. Disconnect the engine coolant fan wiring harness. Note: You stand against driving direction. Unclip the engine coolant fan ...

© 2014-2026 Copyright www.csmans.com
 
0.0058