Chevrolet Sonic Repair Manual: OnStar Description and Operation

This OnStar® system consists of the following components:

• Telematics communication interface control module
• OnStar® three button assembly
• Microphone
• Cellular antenna
• Navigation antenna
• Bluetooth® antenna (If equipped)
• Back up battery (If equipped)

This system also interfaces with the factory installed vehicle audio system.

Telematics Communication Interface Control Module

The telematics communication interface control module is a cellular device that allows the user to communicate data and voice signals over the national cellular network. Power is provided by a dedicated, fused B+ circuit. Ground is provided through the vehicle wiring harness attached to the module. The ignition state is determined by the telematics communication interface control module through serial data messaging.

Dedicated circuits are used to connect the telematics communication interface control module to a microphone, the button assembly, and to command the status LED. The telematics communication interface control module communicates with the rest of the vehicle over the serial data bus.

The module houses 2 technology systems, one to process GPS data, and another for cellular information. The cellular system connects the OnStar® system to the cellular carrier’s communication system by interacting with the national cellular infrastructure. The module sends and receives all cellular communications over the cellular antenna and cellular antenna coax. GPS satellites orbiting earth are constantly transmitting signals of their current location. The OnStar® system uses the GPS signals to provide location on demand.

The module also has the capability of activating the horn, initiating door lock/unlock, or activating the exterior lamps using the serial data circuits. These functions can be commanded by the OnStar® Call Center per a customer request.

OnStar® Three Button Assembly

Base Mirror

• The OnStar® button assembly may be part of the rearview mirror, or a separate, stand alone unit. The button assembly is comprised of 3 buttons and a status LED. The buttons are defined as follows:
• The answer/end call button, which is black with a white phone icon, allows the user to answer and end calls or initiate speech recognition.
• The blue OnStar® call center button, which displays the OnStar® logo, allows the user to connect to the OnStar® call center.
• The emergency button, which displays a white cross with a red background, sends a high priority emergency call to the OnStar® call center when pressed.

The telematics communication interface control module supplies 10 volts to the OnStar® button assembly on the keypad supply voltage circuit. When pressed, each button completes a circuit across a resistor allowing a specific voltage to be returned to the telematics communication interface control module on the keypad signal circuit. Depending upon the voltage range returned the telematics communication interface control module is able to identify which button has been pressed.

The OnStar® status LED is located with the button assembly. The LED is green when the system is ON and operating normally. When the status LED is green and flashing, it is an indication that a call is in progress. When the LED is red, this indicates a system malfunction is present. In the event there is a system malfunction and the OnStar® system is still able to make a call, the LED will flash red during the call.

If the mirror has the rear vision camera disp

Mobile Telephone Microphone Replacement

Mobile Telephone Microphone Replacement Callout Component Name Preliminary Procedure Remove the dome lamp bezel. Refer to Dome ...

Radio Antenna Base Replacement

Radio Antenna Base Replacement Callout Component Name Preliminary Procedure Lower the rear of the headlining trim panel. Refer ...

Other materials:

Driving on Wet Roads
Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep‐standing or flowing water. Warning Wet brakes can cause crashes. They might not work as ...

Liftgate Weatherstrip Replacement
Liftgate Weatherstrip Replacement Callout Component Name 1 Liftgate Weatherstrip Procedure Clean the area where the seal will be mounted. Use a suitable solvent with a mixture of 50?€‰percent isopropyl alc ...

Input Speed Sensor Replacement
Removal Procedure Remove the control solenoid valve and transmission control module assembly. Refer to Control Solenoid Valve and Transmission Control Module Assembly Replacement. Remove the input speed sensor bolt (2) M6 x 23. Unlock t ...

© 2014-2026 Copyright www.csmans.com

 
0.0075