Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Front Wheel Bearing and Hub Replacement

Chevrolet Sonic Repair Manual / Chassis / Suspension / Front Wheel Bearing and Hub Replacement

Special Tools

CH-50559 Wheel Hub/Bearing Remover Kit

For equivalent regional tools, refer to Special Tools.

Removal Procedure
  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  2. Remove the steering knuckle assembly from the vehicle. Refer to Steering Knuckle Replacement.


  3. Position the steering knuckle assembly (1) in a suitable vise.
  4. Position the CH-50059-1 wheel hub/bearing removal/installation bridge assembly (1) and the CH-50559-2 wheel hub/bearing removal/installation adapter (2) on the wheel bearing inner hub.
  5. Using the CH-50059-1 and the CH-50559-2 , remove the wheel hub from the wheel bearing.

  6. If the inner race of the bearing is pulled out with the hub, remove the inner race from the using the appropriate tools (1, 2).

  7. Using the appropriate tool, remove the retaining ring (1) from the steering knuckle.

  8. Position the CH-50559-1 wheel hub/bearing removal/installation bridge assembly (1) and the CH-50559-3 wheel bearing removal adapter (2) on the steering knuckle.
  9. Remove the wheel bearing from the steering knuckle and discard it. Inspect the bore of the of the steering knuckle for pitting, scoring wear, or corrosion. If damage cannot be easily cleaned up with light sanding, replace the steering knuckle.
Installation Procedure


    Note:

    • The bearing must be installed with the rubber seal facing inboard.
    • Ensure that the wheel bearing is evenly seated in the steering knuckle.
  1. Using the CH-50559-4 wheel hub/bearing installation adapter (1) and the appropriate extension and press, install the new bearing into the steering knuckle until it is correctly seated.

  2. Position the CH-50559-4 (1) wheel hub/bearing installation adapter and the appropriate extension to the inside of the bearing and position the CH-50559-2 wheel hub removal/installation adapter and the appropriate extension on the wheel hub.
  3. Press in the hub until it is correctly seated.

  4. Using the appropriate tool, install the retaining ring (1).
  5. Verify the hub rotates smoothly.
  6. Install the steering knuckle assembly in the vehicle. Refer to Steering Knuckle Replacement.
  7. Lower the vehicle.
Lower Control Arm Replacement
Removal Procedure Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. ...

Rear Wheel Bearing and Hub Replacement (Disc Brake)
Special Tools EN–45059 Angle Meter For equivalent regional tools, refer to Special Tools. Removal Procedure Raise and suitably support the vehicle. Refer to Lifting and Jacking ...

Other materials:

Airbag Steering Wheel Module Coil Centering
Note: If a double wire harness strap is installed onto the wire harness assembly and steering column, the original holder for the wire strap(s) MUST be reused during installation. Remove the wire harness strap(s) where necessary. Caution: The new SIR coil assembly will ...

Rear Wheel Bearing and Hub Replacement (Drum Brake)
Rear Wheel Bearing and Hub Replacement Callout Component Name Preliminary Procedures Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the tire and wheel assembly. Refer to Tire and Wheel Rem ...

Air Conditioning Evaporator Core Replacement
Air Conditioning Evaporator Core Replacement Callout Component Name Preliminary Procedure Remove the instrument panel tie bar. Refer to Instrument Panel Tie Bar Replacement. Remove HVAC module. Refer to Heater and Air Con ...

© 2014-2026 Copyright www.csmans.com
 
0.0076