Chevrolet Sonic manuals

Audi Q7 (4M) 2016-2022 Owner's Manual: Maneuver assist

Description

Applies to: vehicles with maneuver assist


Fig. 140 Upper display: maneuver assist

General information

The maneuver assist supports the driver when maneuvering and parking by monitoring the area in front of, behind, and beside the vehicle using sensors. If there is an impending collision with an object, the system will intervene within its limits and attempt to prevent the collision by applying the brakes. The system can detect objects that are approximately 8 inches (20 cm) high or higher.

Display overview

The displays (1) - (4) indicate the status and availability of the maneuver assist.

  1. The white border indicates the availability in this area.
  2. The red border indicates an object nearby.
  3. If there is no border, this indicates an inactive area (partial availability).
  4. Activate/deactivate maneuver assist and status displays:
    • Maneuver assist activated. The vehicle is bordered in white. If the sensors are partially available, the white border will only be visible in the monitored areas.
    • Maneuver assist is temporarily deactivated.
    • (symbol shown in gray) Maneuver assist is not available.
    • No symbol: maneuver assist was switched off completely in the settings.

Braking intervention

Braking intervention can be initiated if there is an impending possible collision with a detected stationary object. If the brakes were applied until the vehicle stopped, Maneuver assist: vehicle has been braked. Obstacle detected will appear in the instrument cluster and you must take over control of the vehicle.

If you continue driving toward the obstacle after the vehicle is braked to a stop, maneuver assist will automatically be temporarily deactivated until the next maneuvering situation.

WARNING

Observe the safety precautions and note the limits of the assist systems, sensors, and cameras.

Tips

Activating or deactivating maneuver assist

Applies to: vehicles with maneuver assist

Requirements

Automatic activation

Maneuver assist activates automatically when reverse gear is engaged while the engine is running.

Deactivating temporarily

If you do not want to use maneuver assist during a parking cycle, you can deactivate it temporarily.

If maneuver assist is deactivated temporarily, it will be activated again automatically the next time park assist is activated.

If you continue driving toward the obstacle after the vehicle is braked to a stop, maneuver assist will automatically be temporarily deactivated until the next maneuvering situation.

Activating manually

You can activate maneuver assist in various ways depending on the situation:

Switching on or off permanently

If maneuver assist is switched off permanently, there will be no symbol in the center of the vehicle graphic (4), fig. 140.

WARNING

Observe the safety precautions and note the limits of the assist systems, sensors, and cameras.

Messages

Applies to: vehicles with maneuver assist

If or is displayed when there is a malfunction, the maneuver assist functions may be unavailable or may be limited.

A message that indicates the cause and possible solution may appear with some displays. The weather conditions may be too poor or a sensor may be covered. Clean the area in front of the sensors and cameras and try to turn the system on again later.

If the malfunction remains, drive to an authorized Audi dealer or authorized Audi Service Facility immediately to have the malfunction corrected.

Parking with the myAudi app
Fig. 139 Upper display: remote controlled parking - preparing the vehicle Requirements The setup has been completed. You are logged into the vehicle with your myAudi user. Bluetooth is s ...

Infotainment system
...

Other materials:

Rear Side Door Window Rear Guide Replacement
Rear Side Door Window Rear Guide Replacement Callout Component Name Preliminary Procedure Remove the rear side door trim panel. Refer to Rear Side Door Trim Replacement. 1 Rear Side Door Window R ...

Throttle Body Heater Inlet Pipe Replacement (LUW)
Throttle Body Heater Inlet Pipe Replacement Callout Component Name Preliminary Procedure Drain the cooling system. Refer to Cooling System Draining and Filling. 1 Throttle Body Heater Inlet Pipe ...

Intake Manifold Cleaning and Inspection
Clean the intake manifold mating surfaces. Inspect the intake manifold (2) for damage. Inspect the intake manifold for cracks near metallic inserts. Inspect the crankcase ventilation passages in the intake manifold face for blockage. Warning: Wear safety glasses in or ...

В© 2014-2022 Copyright www.csmans.com
 
0.0057