Chevrolet Sonic manuals
 

Chevrolet Sonic Repair Manual: Manual Transmission Shift Lever and Selector Lever Cable Replacement

Chevrolet Sonic Repair Manual / Powertrain / Transmission/Transaxle / Transmission Oil Cooler / Shifter Input and Linkage / Manual Transmission Shift Lever and Selector Lever Cable Replacement

Removal Procedure
  1. Remove the battery tray. Refer to Battery Tray Replacement.

    2. \i
  2. Disconnect the shift lever and selector cable ends (1) from the transmission shift lever and selector levers.
  3. Pull the cable retainers (2) to release the shift lever and selector cable from the shift lever and selector cable bracket.
  4. Disconnect the shift lever and selector cables (3) from the shift lever and selector cable bracket.
  5. Remove the floor console. Refer to Front Floor Console Replacement.


  6. Move the floor carpet in order to get access to the gear shift lever and selector cable grommet (1).
  7. Remove the grommet nuts (2).

  8. Lift both cable adjustment retainers (1), one for each cable, to release the shift lever and selector cable.
    9. .1
  9. Pull the shift lever and selector cable retainers (1) from the transmission control assembly (3)
  10. Remove the shift lever and selector cable from the shift lever and selector control.
  11. Pull the shift lever and selector cable assembly through the cowl into the passenger compartment.
  12. Remove the shift lever and selector cable assembly from the vehicle.
Installation Procedure
  1. Position the shift lever and selector cable assembly in the vehicle.
  2. Gently pull the shift lever and selector cable assembly through the cowl into the engine compartment.
    3. \i
  3. Connect the shift lever and selector cable ends (1) to the transmission shift lever and selector lever.
  4. Install the shift lever and the selector lever cable (3) to the shift lever and selector lever cable bracket.

  5. Move the floor carpet in order to get access to the shaft lever and selector lever cable grommet (1).

    6. Caution:

    Refer to Component Fastener Tightening Caution.

  6. Install the grommet nuts and tighten to 9 Y (80 lb in)


    7. .1
  7. Connect the shift lever and selector lever cables to the shaft and selector control adjusters (2).
  8. Install the shift lever and selector lever cable retainers (1) to the transmission control (3).

  9. Press down and Lock both cable adjustment retainers (1) one for each cable, to adjust the shift lever and selector lever cable.
  10. Adjust the shift lever and selector lever cables. Refer to Manual Transmission Shift Lever Cable Adjustment.
  11. Install the floor console. Refer to Front Floor Console Replacement.
  12. Install the battery tray. Refer to Battery Tray Replacement.
  13. Verify correct operation of the transmission control assembly.
Manual Transmission Shift Lever and Selector Lever Cable Adjustment
Remove the floor console. Refer to Front Floor Console Replacement. Lift upward and disengage (do not remove) both cable lock adjusters (1) to release the internal cable asse ...

Range Selector Lever Cable Adjustment
Note: Adjust the automatic transmission range selector cable while the transmission and the gear selector are in the Park position only. Failure to do so may cause mis-adjustment. ...

Other materials:

Courtesy Transportation Program
To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper-to-Bumper (Base Warranty Coverage period in Canada), extended powertrain, and/or hybrid-specific warranties in both the U.S ...

Special Tools
Illustration Tool Number/ Description EL 42059 J 42059 Cigar Lighter Socket Remover ...

Airbag Roof Side Rail Module Replacement - Rear
Airbag Roof Side Rail Module Replacement - Rear Callout Component Name Warning: In order to prevent SIR deployment, personal injury, or unnecessary SIR system repairs, do not strike the door or the door pillar in the ...

В© 2014-2026 Copyright www.csmans.com
 
0.007