Chevrolet Sonic Repair Manual: Transmission Unit
- Ignition Transmission Lock Check
- Transmission Adaptive Functions
- Transmission Assemble (Gen 1)
- Transmission Assemble (Gen 2)
- Transmission Component and System Description
- Transmission Disassemble (Gen 1)
- Transmission Disassemble (Gen 2)
- Transmission General Description
- Transmission Identification Information
- Transmission Indicators and Messages
- Transmission Rear Mount Bracket Replacement
- Transmission Rear Mount Replacement
- Transmission Replacement
- Transmission Replacement (With 1.2L or 1.4L Engine)
- Transmission Replacement (With 1.6L or 1.8L Engine)
- Transmission System Description and Operation
- Vehicle, Engine and Transmission ID and VIN Location, Derivative and Usage
- Fluid Pump Selective Measurement
- Torque Converter Housing with Fluid Pump Assembly Installation (6T30)
- Torque Converter Housing with Fluid Pump Assembly Installation (6T40/45/50 Non Hybrid)
- Torque Converter Housing with Fluid Pump Assembly Removal (Non Hybrid)
- Low and Reverse and 1-2-3-4 Clutch Housing Assemble (6T30)
- Low and Reverse and 1-2-3-4 Clutch Housing Assemble (6T40/45/50)
- Low and Reverse and 1-2-3-4 Clutch Housing Cleaning and Inspection
- Low and Reverse and 1-2-3-4 Clutch Housing Disassemble
- Low and Reverse and 1-2-3-4 Clutch Housing, and 1-2-3-4 Clutch Plate Installation (6T30)
- Low and Reverse and 1-2-3-4 Clutch Housing, and 1-2-3-4 Clutch Plate Installation (6T40/45/50)
- Low and Reverse Clutch Assembly and Low and Reverse Clutch Plate Installation
- Low and Reverse and 1-2-3-4 Clutch Housing, Low and Reverse Clutch Assembly, Output Sun Gear, and 2-6 Clutch Plate Disassemble (Gen 1)
- Low and Reverse and 1-2-3-4 Clutch Housing, Low and Reverse Clutch Assembly, Output Sun Gear, and 2-6 Clutch Plate Disassemble (Gen 2)
- Electronic Park Lock Description and Operation
- Park Brake and P (Park) Mechanism Check
- Control Valve Body Assembly Assemble (Gen 1)
- Control Valve Body Assembly Assemble (Gen 2)
- Control Valve Body Assembly Disassemble (Gen 1)
- Control Valve Body Assembly Disassemble (Gen 2)
- Control Valve Body Assembly Installation
- Control Valve Body Assembly Removal
- Control Valve Body Cleaning and Inspection (Gen 2)
- Control Valve Body Cover Installation
- Control Valve Body Cover Replacement
- Control Valve Body Replacement
Torque Converter Removal
Torque Converter Removal
Callout
Component Name
1
Lock Pin
Warning: Lock pin must be secured into the bench fixt ...
Ignition Transmission Lock Check
While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF
in each shift lever position.
For automatic transmission vehicles, the ignition should turn to LOCK/OFF
onl ...
Other materials:
Replacing LATCH System Parts After a Crash
Warning
A crash can damage the LATCH system in the vehicle. A damaged LATCH system
may not properly secure the child restraint, resulting in serious injury or even
death in a crash. To help make sure the LATCH system is working properly after a
crash, see your dealer to have the system inspec ...
Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a
Punctured Tire
When using the tire sealant and compressor kit during cold temperatures, warm
the kit in a heated environment for five minutes. This will help to inflate the
tire faster.
If a tire goes flat, avoid further tire and wheel damage by driving slowly to
a level place. Turn on the hazard warning fl ...
Crankshaft Position System Variation Learn
Note: The crankshaft position sensor system variation learn procedure
is required when the following service procedures have been performed, regardless
of whether DTC P0315 is set:
Engine replacement
Engine control module (ECM) replacement
Crankshaft damper replacement
...
0.0069